Go Back   Bream Master Forums > Bream Boats > Boating Accessories

Boating Accessories Sounders, Fixings, Safety Gear and More



Reply
 
Thread Tools Rating: Thread Rating: 6 votes, 5.00 average. Display Modes
  #1  
Old 06-09-2009, 06:51 AM
mundz mundz is offline
Mature Bream
 
Join Date: Aug 2003
Location: Calamvale, QLD
Posts: 335
wiring up my boat

hi guys i was wondering if anyone could give me some pointers on wiring up my boat. i have just bought new sounder and nav and anchor lights, plus a switch panel with fuses to run the aforementioned through. i was just wondering what the best way to do it is and if you guys have an on board charger or just hook it up to a normal one at the end of the day. Any help would be greatly appreciated.
__________________
pb bream- 41cm to tip
Reply With Quote
  #2  
Old 06-09-2009, 06:52 AM
forsterfisho's Avatar
forsterfisho forsterfisho is offline
Blue Lip
 
Join Date: Jun 2009
Location: Hornsby, Sydney
Posts: 2,992
Quote:
Originally Posted by mundz View Post
hi guys i was wondering if anyone could give me some pointers on wiring up my boat. i have just bought new sounder and nav and anchor lights, plus a switch panel with fuses to run the aforementioned through. i was just wondering what the best way to do it is and if you guys have an on board charger or just hook it up to a normal one at the end of the day. Any help would be greatly appreciated.
I just use a normal battery charger at the end of the day. I have 2 sets of posts on the battery and just put the charge on the posts that have nothing attached. I am looking at putting a battery isolator onboard, to provide a bit of protection when charging the battery.
__________________
Fishing wasn't meant to be easy, otherwise it would be called catching.



www.crankalures.com
Reply With Quote
  #3  
Old 06-09-2009, 08:09 AM
Brad Y's Avatar
Brad Y Brad Y is offline
Blue Lip
 
Join Date: Apr 2004
Location: Busselton, WA
Posts: 4,861
Use tinned marine rated wire and good quality connectors. Install a battery switch. These will help with any corrosion problems you may run into. Main thing is when your not using the boat, turn the battery power supply off or remove the batteries.

A voltage sensitive relay will come in handy so you can start your outboard off the cranking battery and the alternator on the outboard charges up that battery until its full. Once that battery is full, the relay switches over and will charge your deep cycle battery, giving you more leccy power on the water. But after a days fishing you will still want to charge your battery on mains power. Spend $300 or so on a quality charger that will bulk, top up and maintain your battery and outputs about 10% of your amp hour rating. A 5 amp single stage charger wont keep a 100amp hour battery running as long as a good charger like a guest or c-tek.

Be sure to install waterproof fuse carriers on the positive lines too, sometimes the standard spade carriers will get corrosion issues as well.
Reply With Quote
  #4  
Old 06-09-2009, 05:37 PM
mundz mundz is offline
Mature Bream
 
Join Date: Aug 2003
Location: Calamvale, QLD
Posts: 335
thanks for the replies guys
__________________
pb bream- 41cm to tip
Reply With Quote
  #5  
Old 06-09-2009, 08:53 PM
Mandurah Marine's Avatar
Mandurah Marine Mandurah Marine is offline
Mature Bream
 
Join Date: Aug 2008
Location: Mandurah WA
Posts: 406
wiring

. . . . . also, run some twin core 6mm wire with fuse (15 or 20amp depending on total load) at isolator or battery. Run that up to the dash with earth going to buss and + to either a buss or your switch panel. If you don't solder and seal you can get heat shrink joiners from a marine shop - expensive but worth it - they seal up after crimping, with a lighter.
__________________
_________________________________________
You are always better off being marinated by an aquaholic.

PB: No way, you'll just laugh!

Member of Mandurah Breaming Association
Reply With Quote
  #6  
Old 07-09-2009, 04:36 AM
mundz mundz is offline
Mature Bream
 
Join Date: Aug 2003
Location: Calamvale, QLD
Posts: 335
sorry guys i don't understand a lot of that. just went and had a look at some of the diamgrams given as instructions and am not overly confident in hooking everything up. does anyone know of any diagrams or anything quite simple to understand as in nearly all the diagrams i have there is talk of a buss bar???? sorry these may seem like stupid questions but i'm new to this. basically i have 2nav lights an anchor light and a sounder that i want to connct to a switch panel then to the battery, does anyone know of any diagrams that would explain how to do this easily.
__________________
pb bream- 41cm to tip
Reply With Quote
Reply


Thread Tools
Display Modes Rate This Thread
Rate This Thread:

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On



All times are GMT -4. The time now is 12:48 AM.


Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Google